0 votes
asked by (38 points)
edited by
Win 10 1803

Lenovo Explorer WMR HMD

X-Plane 11.21R2

Turn on controller

Run WMR Portal

Run SteamVR

Run X-Plane 11

Turn on VR

Error reading controller configuration

Nothing is working, stuck in hangar. If I hit Esc I can move to VR cockpit but controller is not working and I cannot go to settings to configure it or calibrate it.

From log.txt

0:04:51.804 I/OVR: User is entering the holodeck.
0:04:51.804 I/WIN: Opened window Settings
0:04:53.378 I/OVR: Initializing VR Subsystem.
0:04:53.378 I/OVR: This device DOES have a proximity sensor.
0:04:53.378 I/JOY: REGISTER Joystick device: holographic - vr/WindowsMR:_0x045E/holographic_0, this is a familiar device.
0:04:53.378 E/JOY: UNCALIBRATED AXIS DETECTED: holographic (vr/WindowsMR:_0x045E/holographic_0) Axis #0, assigned to joy_use_none, has an expected min/max range of [-128.000000, 127.000000], but is calibrated for [0.352941, 0.929412]. You should recalibrate the device in the Settings menu.
0:04:53.378 E/JOY: UNCALIBRATED AXIS DETECTED: holographic (vr/WindowsMR:_0x045E/holographic_0) Axis #1, assigned to joy_use_none, has an expected min/max range of [-128.000000, 127.000000], but is calibrated for [0.023529, 0.501961]. You should recalibrate the device in the Settings menu.
0:04:53.378 E/JOY: UNCALIBRATED AXIS DETECTED: holographic (vr/WindowsMR:_0x045E/holographic_0) Axis #3, assigned to joy_use_none, has an expected min/max range of [-128.000000, 127.000000], but is calibrated for [0.498039, 0.529412]. You should recalibrate the device in the Settings menu.
0:04:53.378 E/JOY: UNCALIBRATED AXIS DETECTED: holographic (vr/WindowsMR:_0x045E/holographic_0) Axis #4, assigned to joy_use_none, has an expected min/max range of [-128.000000, 127.000000], but is calibrated for [0.501961, 0.564706]. You should recalibrate the device in the Settings menu.
0:04:53.378 I/OVR: Adding device 1 (WindowsMR: 0x045E)
0:04:58.766 I/OVR: User is leaving the holodeck.
0:04:58.766 I/OVR: Artificially initializing the VR system for an already-loaded P0.
0:04:58.766 I/OVR: Reading VR conf file: Aircraft/Laminar Research/Cessna 172SP/Cessna_172SP_vrconfig.txt
commented by (18 points)
Not sure if this is related:

When I "wake up" my WMR  VR motion controllers, the following error message appears in X-Plane version 11.21r2

Error reading joystick configuration (.joy) file:
Resources/joystick configs/WMR_right.joy
Errors were:
Unknown button (Button 0)
Unknown button (Button 1)
Unknown button in Configuration Group 1 (Button 2)
Unknown button in Configuration Group 2 (Button 1)

The suggestions in this post did not fix the issue.   (Delete the prefs file)

1 Answer

0 votes
answered by (38 points)

The problem was probably due to steamvr beta update as I read in steam community that many users had WMR controller problems with the last steamvr beta update.

I was opt-in steamvr beta so I had affected.

Opt-out steamvr beta - controller did not worked

Uninstalled and installed again steamvr (opt-out beta) - controller did not worked

Deleted X-Plane Joystick Settings.prf  - controller is working now (I had to re-configure joystick, rudder pedals, etc.)

So finally I managed to solve the issue.

Maybe uninstalling and installing again steamvr wasn't necessary and just opt-out steamvr beta and deleting joystick prefs was enough.

Welcome to X-Plane Q&A, where you can ask support questions and get answers from members of the community.

This site is for X-Plane support questions only. Please search for existing answers before posting your question. Off-topic questions will be locked.

If you’re new, you’ll need to register before asking your first question.

If your question is answered, click on the check mark to select the best response.

Categories

...